A-line skirt sewalong part two: the darts and the waistband

Hello there! Welcome back to week two of the A-line skirt sewalong. In today’s tutorial you’re going to learn how to insert darts, interface the waistband, and attach the waistband to the skirt.

The first thing you need to do is zigzag around all those edges, apart from edge E. Just set your machine to a wide zigzag stitch and whizz your way around all of your pieces. This stops the fabric unravelling. You can see that I’ve done that in the photo below.

Set your machine back to a straight stitch. Now it’s time to insert those darts into piece 2. Working on just one dart at a time, fold the fabric right sides together so that the two diagonal lines of the dart lie on top of one another. The excess fabric should be on the wrong side of the fabric, as shown below.

The trick with darts is to iron them flat, pin them along the sewing line, and sew from the fat end towards the point. Never sew all the way to the point: stop a few stitches early, leave your ends long and tie them in a granny knot. This prevents the end from puckering. You can see one of my finished darts in this photo:

Press the darts towards the centre back of the skirt:

Now you’re going to prepare the waistband. Lay your waistband (piece 3), wrong side up, along your ironing board.

Centre your interfacing, glue side down, on your waistband. The glue side is normally a bit bumpy to the touch. You should have the seam allowance of the waistband showing evenly all the way around the interfacing. You can see this in the photograph below. Following the manufacturer’s instructions, iron the interfacing onto the waistband. It’s advisable to place an old cloth between your iron and the interfacing, to protect your iron.

Now fold your waistband (piece 3) in half lengthways and wrong sides together so that seams F and G are touching. Your waistband will be the right way out. Press along the fold to create a crease. I’ve just pressed mine in the photograph below.

Sew seam BD down the left hand side only of the skirt. With right sides together, pin seam BD of the skirt fabric from top to bottom. If piece 2 is on top of piece 1, you are pinning the seam on the right.

I forgot to take a photo of this stage (sorry!), but here’s a photo of the finished seam, so you can see which side seam you are sewing. It’s the sewn, pressed and therefore slightly sticking up seam on the right. Remember, piece 2 is on top.

With right sides together, sew seam BD of the skirt fabric from top to bottom. Press seam BD open. You can see how I’ve draped the skirt over my ironing board to do this, here:

You are now going to sew the waistband to the skirt. Open out your skirt, so that it is lying right side up.

Open up your waistband. Now line up edge G of the waistband with edge C of the skirt, so that the raw edges of each are together and the stitching line of H is in line with the stitching line of D (not seam BD). The right side of the waistband should lie against the right side of the skirt. Pin seam GC. It should look just like this:

Then continue round the top of the skirt, pinning piece 3 to piece 1 along seam GA. Because the waistband is straight and the skirt is curved, you have to pull gently on the curved skirt to fit the waistband to it, like so:

Once it is pinned into place all the way along, sew all the way along the seam GC and GA. (Make sure you keep edge F out of the way.)

Now unfold the waistband, smoothing it upwards, and press seam GA and GC open on the wrong side. You want all the seam allowances to be pressed upwards towards the top of the waistband too. Then you need to fold the seam allowance on edge F down, over the interfacing, and iron it down. You can see that I’ve done all of this here:

Next, you need to fold the whole waistband in half lengthways, wrong sides together, so that F is folded down to G. It should look like a finished (but unsewn) waistband, like so:

Pin this into place.

I always like to finish my clothing by hand, as it gives such a neat finish. Sew the folded edge of F to the inside of the skirt, taking care that your stitches can’t be seen on the right side. It’s easiest to insert your needle a couple of millimetres above the folded edge of the waistband, and sew through the seam allowances hidden inside. Then bring your needle out on the folded edge of the waistband, a bit further along. Here is my needle in the middle of taking a complete stitch.

Then insert your needle a couple of millimetres above where you have just brought it out. You’ll leave a little trail of tiny stitches on the inside, and nothing at all on the outside. It should look like this on the inside:

When you fold the back of the waistband over, it should look like this from the back of the skirt

and like this from the front:

It’s beginning to look like a skirt! Next week, you’ll be inserting the zipper and finishing the other side seam.

Madeleine

How are you getting on? It’s always great to get feedback, be it questions, comments or suggestions – do let me know if these tutorials are helpful to you.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.